2-3/4" x 1-1/8" Rectangle. Low-profile, trailer light functions as both a clearance light and a side marker light when properly mounted. Durable polycarbonate base and amber acrylic lens. Surface mount. 2-Wire pigtail. PC rated.
Features:
Specs:
A PC-rated light produces a 90-degree angle of light to either side of its centerline for a total of 180 degrees of coverage. This beam pattern can be clearly seen when you are standing directly in front of the light, as well as when you are standing on either side of the light. When properly installed, this type of light can function as both a front clearance light and a side marker light or as a rear clearance light and side marker light.
Surface-mount trailer lights install using a flange or bracket with mounting holes. These lights lay flat against the trailer surface and only require a small, often pre-existing hole, for wiring. Mounting hardware is used to secure the light to the trailer.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today we're taking a look at the Hot Dot LED Clearance and Side Marker Light. This small rectangular trailer light functions as both a clearance and side marker light when properly mounted. LEDs make great replacements for incandescent lights, they last longer, they burn brighter and they're more efficient. With LED systems, you don't have to worry about replacing bulbs or worry about brittle filaments. The unit is completely sealed so it does have a nice weatherproof construction to it. It features the Amber lens.
It's made from a durable plastic construction. It's a surface mount installation, mounting hardware not included. They do have the two pre-drilled mount holes right here. The unit is SAE approved. It's a two wire design.
White wire is your ground wire, yellow wire is your power lead.When it comes to the overall dimensions of the unit, starting with the overall length, that gives us a measurement of 2-3/4" long, the overall height is about 1-1/8", and the overall depth from back to front is about 1/2" deep. The distance between the mount holes, center-on-center, is 2". We're going to go ahead and hook it up to power, that way you can see what it looks like with some power running to it. We'll also be able to turn off our overhead light so you can see it in a lower light setting. You can see here, the unit sends out a nice bright consistent signal.
The lens allows plenty of light to come through. It contains a total of two LEDs or two diodes. The multi-diode design really helps optimize the overall light output. That's going to do it for today's look at the Hot Dot LED Clearance and Side Marker Light.
matches old lights
right light fast shipping
Product received in great condition, installed without any issues. Will provide feedback on longevity of product over time. Very pleased thus far.
Still working after one year
Exactly what I ordered and needed.
Parts are exact fit as I led parts
They had what I wanted, ordering was easy and it was delivered quickly.
exactly what our customer needed was able to get this in a timely manner to get customer back on the road.
I used these to attach to the back of my bike rack. I needed something small and flush mounted. These fit the bill perfectly. I was able to mount two on the rack and wire them to the headlights using the wiring pigtail for my trailer. I found these neat watertight heat shrink butt connectors that have a band of solder in the middle; you interlace the wires, position them in the heat shrink and use a lighter to seal the wires and melt the solder. Very handy!
The bike rack slides into my receiver hitch and extends 2' beyond the back of the vehicle, I wanted to make sure the end of the rack was clearly visible at night.
My 2022 Montana 3231CK had “safety lights” on both sides below the entrance door and over the black pipe cover. It’s difficult to find the exact lite. My original lights had 3 diodes. I was happy to find the above with 2 diodes. Normal installation was quick and easy. Giving the dimensions really helped.
Great product exactly as described and the fitment we needed customer left our location happy. Received parts in a timely manner and no damage.
Perfect fit. Mounting holes on 2" centers just like i needed.
Perfect match for what I needed marker safety light for RV
Exactly what was needed. Paid for next day shipping and it go it the next day.
Perfect match for my 2010 Tiffin Phaeton MH clearance light. That was a real concern because it sits next to four others. Very happy.
Works better than the original one did might just replace the rest of them
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.